Please see below for a list of Tag-Connect™ small footprint debugging/programming cable solutions for NXP MCUs and other devices. Solutions may be available for different sized target board connectors, different debugging/programming protocols or different debuggers. Solutions are also available for either “legged” or “no legs” versions of the plug-of-nails™ target board connectors. Use the debugger links to see further information on these options as applicable to particular debuggers.
ARM20 to 6 Pin Plug-of-Nails™ - No Legs Debugger mating connector: 20 Pin IDC 0.1" Female
The Tag-Connect ARM20-CTX adapter board allows our TC2030-IDC cables to be used for ARM SWD (Serial Wire Debug) applications. Although intended for use with our patented TC2030-IDC (and TC2030-IDC-NL) Plug-of-Nails™ Cables, the adapter may also be useful to people wishing to use 6-pin 0.1" ribbon headers on their PCB instead of the traditional 20-Pin header.
For Lauterbach programmers/debuggers with 20-pin 0.1" female IDC connector, please see the alternative ARM20-CTX-M adapter.
Note: Adapter only supplied. The TC2030-IDC or TC2030-IDC-NL cable is purchased separately, the cables and Segger JLINK seen in the pictures are not included!
The TC2030-IDC-NL is our "No Legs" 6-pin Plug-of-Nails™ programming cable fitted with a 6-pin 0.1" pitch ribbon connector.
With its tiny 0.02 sq inch footprint the TC2030 Tag-Connector has a footprint using about the same PCB space as an 0805 resistor.
The "No Legs" versions of our cables are designed to be held in place by hand for a fast programming operation or can be temporarily retained in place for debugging when used with our TC2030-CLIP boards.
See TC2030-IDC for the "Legged" version which has four additional feet which hold it securely in place on the PCB for debugging or programming use.
Popular applications include programming Atmel AVR, many Renesas MCU's (when used with our TC-Renesas E1 / E8a adapter) and Zilog. Also great for bringing our SPI / IIC / RS232 and test signal access.
Also available in 10"/254mm lengths (TC2030-IDC-NL-10). Contact us for 36" length versions of these cables.
This product is intended to temporarily hold a TC2030 -NL ("No Legs") cable in place on a PCB. This solution will help when board space is at a premium and you need a hands free solution for debugging. Supplied as pack of 3.
We recommend keeping a few spare of these since the tiny boards are easy to misplace when working on the bench.
For a more robust solution consider a TC2030 legged cable.
ARM20 to 6 Pin Plug-of-Nails™ - With Legs Debugger mating connector: 20 Pin IDC 0.1" Female
The Tag-Connect ARM20-CTX adapter board allows our TC2030-IDC cables to be used for ARM SWD (Serial Wire Debug) applications. Although intended for use with our patented TC2030-IDC (and TC2030-IDC-NL) Plug-of-Nails™ Cables, the adapter may also be useful to people wishing to use 6-pin 0.1" ribbon headers on their PCB instead of the traditional 20-Pin header.
For Lauterbach programmers/debuggers with 20-pin 0.1" female IDC connector, please see the alternative ARM20-CTX-M adapter.
Note: Adapter only supplied. The TC2030-IDC or TC2030-IDC-NL cable is purchased separately, the cables and Segger JLINK seen in the pictures are not included!
The TC2030-IDC is our "Legged" 6-pin Plug-of-Nails™ programming cable fitted with a 6-pin 0.1" pitch ribbon connector.
The "Legged" or "With Legs" versions of our cables snap directly into a tiny footprint of holes and pads in your PCB. By eliminating the need for a mating header component, you not only save PCB space but also cost on every board!
See TC2030-IDC-NL for the "No Legs" version which has an even smaller footprint of about the size of an 0805 SMT resistor.
Popular applications include programming Atmel AVR, many Renesas MCU's (when used with our TC-Renesas E1 / E8a adapter) and Zilog. Also great for bringing our SPI / IIC / RS232 and test signal access.
Also available in 10" lengths (TC2030-IDC-10). Contact us for 36" length versions of these cables.
ARM20 to 10 Pin Plug-of-Nails™ - No Legs Debugger mating connector: 20 Pin IDC 0.1" Female
The TC2050-ARM2010 is a Tag-Connect adapter board allowing our TC2050-IDC cables to be used for ARM JTAG and ARM SWD (Serial Wire Debug) applications. Although intended for use with our patented TC2050-IDC Plug-of-Nails™ Cables, the adapter may be useful to people wishing to use 10-pin 0.1" ribbon headers on their PCB.
Picture shows Segger JLINK, an TC2050-ARM2010 adapter pcb and a TC2050-IDC cable.
For Lauterbach programmers/debuggers with 20-pin 0.1″ female IDC connector, please see the alternative TC2050-ARM2010-M adapter instead.
Note: Adapter only supplied, debugger and cable not included!
Tag-Connect's TC2050-IDC-NL "No Legs" Plug-of-Nails™ programming cable is a 10-conductor cable fitted with a spring-pin Tag-Connector that conveniently plugs directly into your PCB and terminates in a 0.1" ribbon connector.
Plugs straight to your PCB - No mating connector or header required!
Requires only a tiny 0.03" footprint of pads and locating holes in your PCB.
Zero Cost Per Board!
Tiny Footprint!
High-Reliability Spring-Pins make a Secure Connection and are rated for over 100,000 operations.
Footprint has no height and can reduce the size and space requirements of your PCB.
A great way to make test and debug signals available at no cost and with minimal board space.
Can be retained in place using a TC2050-CLIP board.
Tag-Connect cables provide a simple, reliable means of connecting Debuggers and Programmers or other test equipment to your PCB's while lowering board costs and facilitating efficient production programming. Tag-Connect uses a specially designed (Patent Pending) connector which eliminates the need for putting a programming header or other mating connector on every PCB. Instead, Tag-Connect uses tried and tested spring-pins rated for over 100,000 operations to make a secure connection to a special footprint pattern of pads and locating holes in your PCB.
The tiny "No Legs" footprint takes only 0.03 square inches (about the same board space as a couple of SMT resistors) which means you can locate the footprint right next to the MCU if desired.
This 10-conductor cable has a TC2050-NL Tag-Connector on one end and a standard 0.1" ribbon connector on the other and is suitable for use with most many MCUs / FPGAs and JTAG programming and debug operations.
A growing range of adaptors are available for specific and generic applications such as Xilinx SPARTAN and VERTEX FPGAs, TI MSP430 (TC2050-IDC-430), etc
Also available in self-retaining "legged" version TC2050-IDC.
This product is intended to temporarily hold a TC2050-NL cable in place on a PCB. The solution will help when board space is premium and you need to perform a hands-free programming or debugging operation. For a more robust and convenient debugging connection consider using the TC2050 legged cable and footprint. Supplied as pack of 3.
We recommend keeping a few spare of these since they are easily misplaced when working on the desktop. Over time they may lose some grip.
ARM20 to 10 Pin Plug-of-Nails™ - With Legs Debugger mating connector: 20 Pin IDC 0.1" Female
The TC2050-ARM2010 is a Tag-Connect adapter board allowing our TC2050-IDC cables to be used for ARM JTAG and ARM SWD (Serial Wire Debug) applications. Although intended for use with our patented TC2050-IDC Plug-of-Nails™ Cables, the adapter may be useful to people wishing to use 10-pin 0.1" ribbon headers on their PCB.
Picture shows Segger JLINK, an TC2050-ARM2010 adapter pcb and a TC2050-IDC cable.
For Lauterbach programmers/debuggers with 20-pin 0.1″ female IDC connector, please see the alternative TC2050-ARM2010-M adapter instead.
Note: Adapter only supplied, debugger and cable not included!
Tag-Connect's TC2050-IDC "Legged" Plug-of-Nails™ programming cable is a 10-conductor cable fitted with a spring-pin Tag-Connector that conveniently plugs directly into your PCB and terminates in a 0.1" ribbon connector.
Plugs straight to your PCB - No mating connector or header required!
Requires only a tiny footprint of pads and locating holes in your PCB.
Zero Cost Per Board!
Tiny Footprint!
High-Reliability Spring-Pins make a Secure Connection and are rated for over 100,000 operations.
Footprint has no height and can reduce the size and space requirements of your PCB.
A great way to make test and debug signals available at no cost and with minimal board space.
Tag-Connect cables provide a simple, reliable means of connecting Debuggers and Programmers or other test equipment to your PCB's while lowering board costs and facilitating efficient production programming. Tag-Connect uses a specially designed (Patent Pending) connector which eliminates the need for putting a programming header or other mating connector on every PCB. Instead, Tag-Connect uses tried and tested spring-pins rated for over 100,000 operations to make a secure connection to a special footprint pattern of pads and locating holes in your PCB.
The legged version footprint takes about the same board space as two or three SMT resistors which means you can locate the footprint right next to the MCU if desired.
This 10-conductor cable has a TC2050 Tag-Connector on one end and a standard 0.1" ribbon connector on the other and is suitable for use with most many MCUs / FPGAs and JTAG programming and debug operations.
A growing range of adaptors are available for specific and generic applications such as Xilinx SPARTAN and VERTEX FPGAs, TI MSP430 (TC2050-IDC-430), etc
See also TC2050-IDC-NL (no-legs) version with a tiny 0.03” footprint.
Cortex 10 Pin solutions with 6 Pin target connector
Cortex 10 Pin to 6 Pin Plug-of-Nails™ - No Legs Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
6-Pin "No Legs" TC2030 Plug-of-Nails™ programming cable for use with ARM Cortex processors.
This special cable has a 6-pin TC2030-NL Tag-Connector and a 10-pin ribbon connector that mates with the FTSH-105 style micro-headers used for Cortex Debug as found in debuggers such as Keil's ULINK-2.
The footprint for the TC2030-CTX-NL Plug-of-Nails™ Connector saves over 66% of the PCB space used by typical FTSH-105 style micro-headers!
Please refer to the TC2030-IDC-NL datasheet below for details of the TC2030-NL footprint.
You may also want to purchase a couple of TC2030-CLIP boards which will hold this cable in place for hands-free programming and debugging.
See also the TC2030-CTX "Legged" version of the cable.
For traditional ARM JTAG solutions using the 20-pin header as found on Segger's J-LINK see our TC2050-ARM2010 adapter used with TC2050-IDC (-NL) cables.
WARNING for ATMEL-ICE users: The Atmel-ICE has it's header pin numbers reversed (standard pin 1 is Atmel-ICE's pin 10). To use our cable with Atmel's reversed pin-number header you'll either need to cut off the ribbon connector locating lug and plug it in backwards, or select the LEMTA option below to order with the 10-pin ribbon connector fitted backwards. If you plug in a standard (correct) Cortex cable you're going to short power and stuff out.Note: Cable only supplied, Keil's ULINK2 debugger and Tag-Connect Demo PCB and additional Legged Cable are shown for illustrative use only - not included with the cable!
Datasheets (TC2030-NL is for footprint information only)
This product is intended to temporarily hold a TC2030 -NL ("No Legs") cable in place on a PCB. This solution will help when board space is at a premium and you need a hands free solution for debugging. Supplied as pack of 3.
We recommend keeping a few spare of these since the tiny boards are easy to misplace when working on the bench.
For a more robust solution consider a TC2030 legged cable.
Cortex 10 Pin to 6 Pin Plug-of-Nails™ - With Legs Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
6-Pin Legged TC2030 Plug-of-Nails™ programming cable for use with ARM Cortex processors.
This special cable has a 6-pin TC2030 Tag-Connector and a 10-pin ribbon and ribbon connector that mates with the FTSH-105 style micro-headers used for Cortex Debug Connector as found in debuggers such as Keil's ULINK-2.
See also the TC2030-CTX-NL "No Legs" version of the cable with footprint that saves over 66% of the board space needed by typical FTSH-105 micro headers!
For traditional ARM solutions using the 20-pin header as found on Segger's J-LINK see our TC2050-ARM2010 adapter used with TC2050-IDC (-NL) cables.
WARNING for ATMEL-ICE users: The Atmel-ICE has it's header pin numbers reversed (standard pin 1 is Atmel ICE's pin 10). To use our cable with Atmel's reversed pin-number header you'll either need to cut off the ribbon connector locating lug and plug it in reversed, or select the LEMTA option with the 10-pin connector fitted backwards. If you plug in a standard (correct) Cortex cable you're going to short power and stuff out.Note: Cable only supplied, Keil's ULINK2 debugger and Tag-Connect Demo PCB shown for illustrative use - not included with the cable!
Cortex 20 Pin solutions with 6 Pin target connector
Cortex 20 Pin to 6 Pin Plug-of-Nails™ - No Legs Debugger mating connector: 20 Pin IDC 0.05" Female (Mates with FTSH)
This Cortex programming cable is the same as the TC2030-CTX-NL cable except it has a 0.05" (1.27mm) pitch 20-pin connector compatible with i-Jet and ULINK pro. This won't fit the traditional 20-pin 0.1" connector such as found on the standard J-Link debuggers).
The cable itself has a ten pin ribbon cable and 6-pin TC2030-NL "No legs" Tag-Connect small footprint supporting ARM Cortex MCU's.
Note: Cable only supplied, IAR's I-JET and demo board not included!
This product is intended to temporarily hold a TC2030 -NL ("No Legs") cable in place on a PCB. This solution will help when board space is at a premium and you need a hands free solution for debugging. Supplied as pack of 3.
We recommend keeping a few spare of these since the tiny boards are easy to misplace when working on the bench.
For a more robust solution consider a TC2030 legged cable.
Cortex 20 Pin to 6 Pin Plug-of-Nails™ - With Legs Debugger mating connector: 20 Pin IDC 0.05" Female (Mates with FTSH)
This Cortex programming cable is the same as the TC2030-CTX cable except it has a 0.05" (1.27mm) pitch 20-pin connector compatible with i-Jet and ULINK pro. This won't fit the traditional 20-pin 0.1" connector such as found on the standard J-Link debuggers).
The cable itself has a ten pin ribbon cable and 6-pin TC2030 Tag-Connect footprint supporting ARM Cortex MCU's.
Note: Cable only supplied, IAR's I-JET and demo board not included!
Cortex 20 Pin solutions with 6+10 Pin target connector
Cortex 20 Pin to 6 Pin + 10 Pin Plug-of-Nails™ - With Legs Debugger mating connector: 20 Pin IDC 0.05" Female (Mates with FTSH)
TC2030-CTX-ETM is a TC2030-CTX-20 programming cable with 6-pin Tag-Connector for SWD and an additional 10-pin TC2050 connector connected to pins 11-20 providing the extended trace signals.
The pin numbering for pins 11-20 of the 0.05" pitch 20-pin Cortex maps to the TC2050 pin numbering as follows (TC2050 pins are numbered like a DIP IC).
TC2050 pin no.
Cortex 20-pin
1
11 GND/TgtPwr+cap
2
13 GND/TgtPwr+cap
3
15 GND
4
17 GND
5
19 GND
6
20 TRACEDATA[3]
7
18 TRACEDATA[2]
8
16 TRACEDATA[1]
9
14 TRACEDATA[0]
10
12 TRACECLK
TC2030 pin no.
SWD signal
1
1 VCC
2
2 SWDIO
3
10 nRESET
4
4 SWCLK
5
3,5,9 GND
6
6 SWO
Please Note: Be sure to follow manufacturer's advice on signal integrity and termination during design and layout.
6 Pin to 6 Pin Plug-of-Nails™ – No Legs Debugger mating connector: 6 Pin IDC 0.1" Female
The TC2030-IDC-NL is our "No Legs" 6-pin Plug-of-Nails™ programming cable fitted with a 6-pin 0.1" pitch ribbon connector.
With its tiny 0.02 sq inch footprint the TC2030 Tag-Connector has a footprint using about the same PCB space as an 0805 resistor.
The "No Legs" versions of our cables are designed to be held in place by hand for a fast programming operation or can be temporarily retained in place for debugging when used with our TC2030-CLIP boards.
See TC2030-IDC for the "Legged" version which has four additional feet which hold it securely in place on the PCB for debugging or programming use.
Popular applications include programming Atmel AVR, many Renesas MCU's (when used with our TC-Renesas E1 / E8a adapter) and Zilog. Also great for bringing our SPI / IIC / RS232 and test signal access.
Also available in 10"/254mm lengths (TC2030-IDC-NL-10). Contact us for 36" length versions of these cables.
This product is intended to temporarily hold a TC2030 -NL ("No Legs") cable in place on a PCB. This solution will help when board space is at a premium and you need a hands free solution for debugging. Supplied as pack of 3.
We recommend keeping a few spare of these since the tiny boards are easy to misplace when working on the bench.
For a more robust solution consider a TC2030 legged cable.
6 Pin to 6 Pin Plug-of-Nails™ – With Legs Debugger mating connector: 6 Pin IDC 0.1" Female
The TC2030-IDC is our "Legged" 6-pin Plug-of-Nails™ programming cable fitted with a 6-pin 0.1" pitch ribbon connector.
The "Legged" or "With Legs" versions of our cables snap directly into a tiny footprint of holes and pads in your PCB. By eliminating the need for a mating header component, you not only save PCB space but also cost on every board!
See TC2030-IDC-NL for the "No Legs" version which has an even smaller footprint of about the size of an 0805 SMT resistor.
Popular applications include programming Atmel AVR, many Renesas MCU's (when used with our TC-Renesas E1 / E8a adapter) and Zilog. Also great for bringing our SPI / IIC / RS232 and test signal access.
Also available in 10" lengths (TC2030-IDC-10). Contact us for 36" length versions of these cables.
10 Pin to 10 Pin Plug-of-Nails™ – No Legs Debugger mating connector: 10 Pin IDC 0.1" Female
Tag-Connect's TC2050-IDC-NL "No Legs" Plug-of-Nails™ programming cable is a 10-conductor cable fitted with a spring-pin Tag-Connector that conveniently plugs directly into your PCB and terminates in a 0.1" ribbon connector.
Plugs straight to your PCB - No mating connector or header required!
Requires only a tiny 0.03" footprint of pads and locating holes in your PCB.
Zero Cost Per Board!
Tiny Footprint!
High-Reliability Spring-Pins make a Secure Connection and are rated for over 100,000 operations.
Footprint has no height and can reduce the size and space requirements of your PCB.
A great way to make test and debug signals available at no cost and with minimal board space.
Can be retained in place using a TC2050-CLIP board.
Tag-Connect cables provide a simple, reliable means of connecting Debuggers and Programmers or other test equipment to your PCB's while lowering board costs and facilitating efficient production programming. Tag-Connect uses a specially designed (Patent Pending) connector which eliminates the need for putting a programming header or other mating connector on every PCB. Instead, Tag-Connect uses tried and tested spring-pins rated for over 100,000 operations to make a secure connection to a special footprint pattern of pads and locating holes in your PCB.
The tiny "No Legs" footprint takes only 0.03 square inches (about the same board space as a couple of SMT resistors) which means you can locate the footprint right next to the MCU if desired.
This 10-conductor cable has a TC2050-NL Tag-Connector on one end and a standard 0.1" ribbon connector on the other and is suitable for use with most many MCUs / FPGAs and JTAG programming and debug operations.
A growing range of adaptors are available for specific and generic applications such as Xilinx SPARTAN and VERTEX FPGAs, TI MSP430 (TC2050-IDC-430), etc
Also available in self-retaining "legged" version TC2050-IDC.
This product is intended to temporarily hold a TC2050-NL cable in place on a PCB. The solution will help when board space is premium and you need to perform a hands-free programming or debugging operation. For a more robust and convenient debugging connection consider using the TC2050 legged cable and footprint. Supplied as pack of 3.
We recommend keeping a few spare of these since they are easily misplaced when working on the desktop. Over time they may lose some grip.
10 Pin to 10 Pin Plug-of-Nails™ – With Legs Debugger mating connector: 10 Pin IDC 0.1" Female
Tag-Connect's TC2050-IDC "Legged" Plug-of-Nails™ programming cable is a 10-conductor cable fitted with a spring-pin Tag-Connector that conveniently plugs directly into your PCB and terminates in a 0.1" ribbon connector.
Plugs straight to your PCB - No mating connector or header required!
Requires only a tiny footprint of pads and locating holes in your PCB.
Zero Cost Per Board!
Tiny Footprint!
High-Reliability Spring-Pins make a Secure Connection and are rated for over 100,000 operations.
Footprint has no height and can reduce the size and space requirements of your PCB.
A great way to make test and debug signals available at no cost and with minimal board space.
Tag-Connect cables provide a simple, reliable means of connecting Debuggers and Programmers or other test equipment to your PCB's while lowering board costs and facilitating efficient production programming. Tag-Connect uses a specially designed (Patent Pending) connector which eliminates the need for putting a programming header or other mating connector on every PCB. Instead, Tag-Connect uses tried and tested spring-pins rated for over 100,000 operations to make a secure connection to a special footprint pattern of pads and locating holes in your PCB.
The legged version footprint takes about the same board space as two or three SMT resistors which means you can locate the footprint right next to the MCU if desired.
This 10-conductor cable has a TC2050 Tag-Connector on one end and a standard 0.1" ribbon connector on the other and is suitable for use with most many MCUs / FPGAs and JTAG programming and debug operations.
A growing range of adaptors are available for specific and generic applications such as Xilinx SPARTAN and VERTEX FPGAs, TI MSP430 (TC2050-IDC-430), etc
See also TC2050-IDC-NL (no-legs) version with a tiny 0.03” footprint.
14 Pin to 14 Pin Plug-of-Nails™ – No Legs Debugger mating connector: 14 Pin IDC 0.1" Female
14-pin Plug-of-Nails™ programming/debug cable - No Legs Version
Fitted with 14-pin (2x7) 0.1" spaced ribbon cable connector.
Approx 8" (200mm) of ribbon cable between connectors.
See also TC2070-IDC (legged) version.
Note that for many applications where 14-pin connectors are natively used by a debugger (such as MSP430, TI and ADI DSP's, Renesas MCU's etc) we offer some excellent alternative solutions that in many cases can reduce the footprint size on your PCB to 6 or 10-pins as well as reducing the price per cable.
GRIP-14 is used to hold a TC2070 -NL cable to the PCB.
The GRIP presses onto the three alignment pins from underneath the PCB and grips tightly. It is non-conductive.
This is one pack, three in a pack.
14 Pin to 14 Pin Plug-of-Nails™ – With Legs Debugger mating connector: 14 Pin IDC 0.1" Female
14-pin Plug-of-Nails™ programming cable - With Legs Version
Fitted with 14-pin (2x7) 0.1" spaced ribbon cable connector.
Approx 8" (200mm) of ribbon cable between connectors.
Note that for many applications where 14-pin connectors are natively used by a debugger (such as MSP430, TI and ADI DSP's, Renesas MCU's etc) we offer some excellent alternative solutions that in many cases can reduce the footprint size on your PCB to 6 or 10-pins as well as reducing the price per cable.
1 x TC2030-IDC-NL
1 x TC2030-CTX-NL 6-Pin "No Legs" Cable with 10-pin micro-connector for Cortex processors
1 x TC2030-CTX-ETM
1 x TC2070-IDC-NL
1 x TC2070-IDC