MPLAB® ICD 3 In-Circuit Debugger System is Microchip’s most cost effective high-speed hardware debugger/programmer for Microchip Flash Digital Signal Controller (DSC) and microcontroller (MCU) devices.
Tag-Connect™ replacement debug/programming cables save cost and space on every board!
The TC2030-MCP family cables are designed for Microchip and compatible debuggers that use a Modular RJ12 Connector. Just plug our cable in. This solution also works with MPLAB ICD 2 and MPLAB REALICE.
Now get going and start debugging!
Both “legged” and “no-leg” cables come in the standard length, as well as the longer 10″ cables.
The TC2030-MCP-NL will require the TC2030-CLIP if you want a hands-free solution while debugging.
RJ12 to 6 Pin Plug-of-Nails™ - No Legs (standard cable)
PCB End: 6 Pin Plug-of-Nails™ No Legs
Debug End: 6 Pin RJ11/RJ12
Tag-Connect TC2030-MCP-NL programming cable is primarily intended for use in production programming. It is particularly suited to environments where the connection to the PCB is of short duration, and operators are working quickly from board to board.
A major advantage of the TC2030-MCP-NL is the extremely small footprint required on the PCB (hardly any bigger than a surface mount resistor) allowing the minimum possible space on your PCB to be used for the programming connection.
The TC2030-MCP-NL is also compatible with the TC2030-MCP footprint allowing use of the TC2030-MCP for development work and TC2030-MCP-NL for fast programming in production.
The TC2030-MCP-NL can be held in place making it suitable for debugging and development when using TC2030-CLIP board .
Where a sustained connection to the PCB is required, also consider the TC2030-MCP.
Ideal for efficient production programming and also for debugging.
This product is intended to temporarily hold a TC2030 -NL ("No Legs") cable in place on a PCB. This solution will help when board space is at a premium and you need a hands free solution for debugging. Supplied as pack of 3.
We recommend keeping a few spare of these since the tiny boards are easy to misplace when working on the bench.
For a more robust solution consider a TC2030 legged cable.
RJ12 to 6 Pin Plug-of-Nails™ - With Legs (standard cable)
PCB End: 6 Pin Plug-of-Nails™ Legged
Debug End: 6 Pin RJ11/RJ12
Tag-Connect TC2030-MCP cable is primarily intended for use in development environments and is also ideal for production programming. The spring-loaded contact pins are held firmly in place by four plastic legs each of which clips securely into its own locating hole.
Tag-Connect TC2030-MCP is ideal where you need to maintain a connection to the PCB for an extended period such as when performing testing or development work.
See also TC2030-MCP-NL for applications where an even smaller footprint is required.
Ideal for both debugging and production programming.
RJ12 to 6 Pin Plug-of-Nails™ - No Legs (10" cable)
PCB End: 6 Pin Plug-of-Nails™ No Legs
Debug End: 6 Pin RJ11/RJ12
This is the 10"/254mm (longer) version of the TC2030-MCP-NL programming cable.
Note that 10" exceeds the Microchip maximum?cable length specification of 8" and is not supported by Microchip. However, the additional length provides increased convenience and has not been known to cause problems in general use.
Microchip to date has only specified the maximum length of the programming cable and not the typical additional length of PCB traces needed between the RJ12 connector (which might be on the edge of the PCB) and the MCU. With the much smaller TC2030 footprint you can usually put the ICD connection right at the MCU.
This product is intended to temporarily hold a TC2030 -NL ("No Legs") cable in place on a PCB. This solution will help when board space is at a premium and you need a hands free solution for debugging. Supplied as pack of 3.
We recommend keeping a few spare of these since the tiny boards are easy to misplace when working on the bench.
For a more robust solution consider a TC2030 legged cable.
RJ12 to 6 Pin Plug-of-Nails™ - With Legs (10" cable)
PCB End: 6 Pin Plug-of-Nails™ Legged
Debug End: 6 Pin RJ11/RJ12
This is the 10" (254mm) (longer) version of the TC2030-MCP programming cable.
Note that 10" exceeds the Microchip maximum cable length specification of 8" and is not supported by Microchip. However, the additional length provides increased convenience and has not been known to cause problems in general use.
Microchip to date has only specified the maximum length of the programming cable and not the typical additional length of PCB traces needed between the RJ12 connector (which might be on the edge of the PCB) and the MCU. With the much smaller TC2030 footprint you can usually put the ICD connection right at the MCU.
